ESP32 – Electroslab

ESP32 – Electroslab

4.7
(151)
Écrire un avis
Plus
€ 5.00
Ajouter au panier
En Stock
Description

1- 802.11 b/g/n 2- 802.11 n (2.4 GHz), up to 150 Mbps 3- WMM 4- TX/RX A-MPDU, RX A-MSDU 5- Immediate Block ACK 7- Defragmentation 8- Automatic Beacon monitoring (hardware TSF) 9- 4 × virtual Wi-Fi interfaces
The Esp32 DevKit v1 is one of the development board created to evaluate the ESP-WROOM-32 module. It is based on the ESP32 microcontroller that boasts Wifi, Bluetooth, Ethernet and Low Power support all in a single chip. ESP32 is already integrated antenna and RF balun, power amplifier, low-noise amplifiers, filters, and power management module. The entire solution takes up the least amount of printed circuit board area. This board is used with 2.4 GHz dual-mode Wi-Fi and Bluetooth chips by TSMC 40nm low power technology. Flash Layout The internal flash of the ESP32 module is organized in a single flash area with pages of 4096 bytes each. The flash starts at address 0x00000, but many areas are reserved for Esp32 IDF SDK. There exist two different layouts based on the presence of BLE support. Power Power to the Esp32 DevKit v1 is supplied via the on-board USB Micro B connector or directly via the “VIN” pin. The power source is selected automatically. The device can operate on an external supply of 6 to 20 volts. If using more than 12V, the voltage regulator may overheat and damage the device. The recommended range is 7 to 12 volts. Connect, Register, Virtualize and Program The Esp32 DevKit v1 comes with a serial-to-usb chip on board that allows programming and opening the UART of the ESP32 module. Specifications: Microcontroller: Tensilica 32-bit Single-/Dual-core CPU Xtensa LX6 Operating Voltage: 3.3V Input Voltage: 7-12V Digital I/O Pins (DIO): 25 Analog Input Pins (ADC): 6 Analog Outputs Pins (DAC): 2 UARTs: 3 SPIs: 2 I2Cs: 3 Flash Memory: 4 MB SRAM: 520 KB Clock Speed: 240 Mhz Wi-Fi: IEEE 802.11 b/g/n/e/i Integrated TR switch, balun, LNA, power amplifier, and matching network WEP or WPA/WPA2 authentication, or open networks  

Esp32 Wroom 32 Official Wholesale

The UNO R4 was created with maximum compatibility in mind and keeps the same physical factor, compatibility with shields, and 5V operating voltage as its predecessor. The Renesas RA4M1 32-bit Cortex-M4 CPU, which powers the UNO R4, significantly increases processing speed, memory capacity, and functionality.

Arduino Uno R4 WiFi - ABX00087

Male to Male Dupont Line 40 Pin 20cm, Electroslab

Overview, The Arduino UNO R4 WiFi combines the processing power and exciting new peripherals of the RA4M1 microcontroller from Renesas with the

Arduino UNO R4 Wifi Copy

ElectroSlab (@electroslab) • Instagram photos and videos

HFS-DC06 Microwave Radar Sensor – Electroslab

2PCS طقم مفك براغي عضم, Electroslab

The UNO R4 was created with maximum compatibility in mind and keeps the same physical factor, compatibility with shields, and 5V operating voltage as its predecessor. The Renesas RA4M1 32-bit Cortex-M4 CPU, which powers the UNO R4, significantly increases processing speed, memory capacity, and functionality.

Arduino Uno R4 WiFi - ABX00087

ElectroSLab – Electroslab

LCD1602 LCD 1602 IIC/I2C Blue Backlight, Electroslab

Communication Modules – Electroslab